IEI Technology IAP-6002-WG+ Industrial PoE 802.11 b/g Access Point

IAP-6002-WG/WG+ is a reliable 802.11b/g WLAN with 2 ports LAN Access Point. It can be configured to operate in AP/Bridge/Repeater/AP-Client mode. You are able to configure IAP-6002-WG/WG+ by WEB interface via LAN port or WLAN interface. IAP-6002-WG/WG+ provides dual Ethernet ports in switch mode, so that you can use Daisy Chain to reduce the usage of Ethernet switch ports. In addition, IAP-6002-WG+ also provides PD feature on ETH2 which is fully compliant with IEEE802.3af P.O.E. PD specification. Therefore, IAP-6002-WG/ WG+ are one of the best communication solutions for wireless applications on the industrial network.

Features

• WLAN interface support up to 54Mbps link speed
• Various kinds of operation modes supported: AP/ Bridge/Repeater/AP-Client mode
• Various kinds of encryption supported: WEP/ WPA/WPA-PSK(TKIP,AES)/WPA2/ WPA2- PSK(TKIP,AES)/Radius
• Dual redundant Ethernet port support redundant mode (Recovery time < 10ms)
• Ethernet switch mode enable Daisy Chain
• Wireless connecting status monitoring
• Versatile modes & event alarm by e-mail
• HTTPs & SSH protocol supported for secured management
• IP table to prevent access from unauthorized IP address
• IP Configurable by Windows utility (AP-Tool)
• 1KV isolation for PoE PD port of IAP-6002-WG+
• Dual redundant DC power inputs of terminal block
• Rigid IP-30 housing design
• DIN-Rail and panel mounting enabled

Specifications

ORing AP Model	IAP-6002-WG	IAP-6002-WG+
Physical Ports
10/100Base-T(X) Ports in RJ45 Auto MDI/MDIX	2	2
P.O.E. PD port		Present at ETH2 Fully compliant with IEEE 802.3af Power Device specification Over load & short circuit protection Isolation Voltage: 1000 VDC min. Isolation Resistance : 108 ohms min
WLAN interface
Operating Mode	AP/Bridge/Repeater/AP-Client
Antenna Connector	Reverse SMA
Radio Frequency Type	DSSS
Modulation	IEEE802.11b: CCK, DQPSK, DBPSK IEEE802.11g: OFDM with BPSK, QPSK, 16QAM, 64QAM
Frequency Band	America/FCC: 2.412~2.462 GHz (11 channels) Europe CE/ETSI: 2.412~2.472 Ghz (13 channels)
Transmission Rate	IEEE802.11b: 1/ 2/ 5.5/ 11 Mbps IEEE802.11g: 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps
Transmit Power	IEEE802.11b/g: 18dBm
Receiver Sensitivity	-81dBm @ 11Mbps, PER< 8%; -64dBm @ 54Mbps, PER< 10%
Encryption Security	WEP: (64-bit ,128-bit key supported) WPA: WPA2 :802.11i(WEP and AES encryption) PSK (256-bit key pre-shared key supported) Radius supported TKIP encryption
Wireless Security	SSID broadcast disable
LED indicators
Power indicator	PWR 1(2)(P.O.E.) / Ready: Red On: Power is on and booting up. Red Blinking: Indicates an IP conflict, or DHCP or BOOTP server did not respond properly. Green On: Power is on and functioning Normally. Green Blinking: Located by Administrator.
10/100TX RJ45 port indicator	Green for port Link/Act at 100Mbps. Yellow for port Link/Act at 10Mbps
WLAN LEDs:	WLAN Link /ACT: Green WLAN Strength: 1<25%, 2<50%, 3<75%, 4<100%
Fault	Red: Ethernet link down or power down
Fault contact
Relay	Relay output to carry capacity of 1A at 24VDC
Power
Redundant Input power	Dual DC inputs. 12-48VDC on 6-pin terminal block
Power consumption (Typ.)	6 Watts	6 Watts
Overload current protection	Present
Reverse polarity protection	Present on terminal block
Physical Characteristic
Enclosure	IP-30
Dimension (W x D x H)	52(W)x106(D)x144(H) mm (2.05x4.17x5.67 inch.)
Environmental
Storage Temperature	-40 to 85°C (-40 to 185°F)
Operating Temperature	-10 to 55°C (14 to 140°F)
Operating Humidity	5% to 95% Non-condensing
Regulatory approvals
EMI	FCC Part 15, CISPR (EN55022) class A
EMS	EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock	IEC60068-2-27
Free Fall	IEC60068-2-32
Vibration	IEC60068-2-6
Safety	EN60950
Warranty	5 years

If you need accessory information for this product, please use our Online Contact Us Form , our industrial sales team is here to help you find the accessories.

Download DataSheet