ACCES I/O 

ACCES I/O 104-PWR-500A-48 DC/DC power module, 48V nominal input, 5V only output at 8A, -40 to +105 C

Mfg Part Number:  104-PWR-500A-48  
Image may not reflect the actual item.
Price: $129.00
Quantity:
Status: Active
No Sales Tax except these states
, PO and Wire.
FEATURES
  • PC/104 Bus 30/40Watt DC/DC Power Supply
  • Up to 84% Efficiency
  • Three Wide Input Voltage Ranges:
    • 12V Nominal, 9VDC-18VDC(30W)
    • 24V Nominal, 18VDC-36VDC(40W)
    • 48V Nominal, 36VDC-75VDC(40W)
  • Output Voltage and Current:
    • +12V Input: +5VDC at 6A Max
    • +24V Input: +5VDC at 8A Max
    • +48V Input: +5VDC at 8A Max
  • Voltage Status LEDs
  • Reverse Power Protection on Inputs
  • Resettable Fused Input Line
  • Fully Protected Outputs
  • Can be populated on either side of the board to allow for heat-sinking in fanless application requirements
  • Temperature range with heatsink -40 to +65°C, up to 105°C with derating of 2% per °C (no air flow)

    • FUNCTIONAL DESCRIPTION

    The design incorporates a 16-bit pass through PC/104 connector, molex type power input connector and voltage status LED?s. Since heat is always a factor to consider in any system design project, this module can be populated on either side of the board to facilitate heat sinking to one end of an enclosure, with the CPU heat sinking to the other end of the enclosure.

    This single output version can be ordered with or without a heatsink. At up to 84% efficiency, a dynamic input range and full protection on inputs and outputs, this power supply is very versatile and appropriate for many PC/104 based applications.

    The Input Power Connector is a Four-pin standard Molex type connector at the edge of the board. It?s the same connector as used on a CD-ROM so it?s easy to set up and test a system with a local +12V Computer type power supply.

    Output Characteristics

    • OutputVoltage Set Point on 5V: ±1%, Factory set
    • Load Regulation: ±0.5%, Measured from Full Load to 10% load
    • Temperature Coeffcient: ±0.01%/°C
    • Ripple/Noise on 5V: 60mV P-P measured at 20MHz bandwidth
    • Short Circuit Protection: Indefinite, Automatic Recovery
    • Overvoltage Protection: 120% Clamp type

    Input Characteristics

    Input Characteristics 12 24 48 Unit/Comments
    Input Voltage 9-18 18-36 36-75 VDC
    Under Voltage Shut Down 8 16 33 VDC (min)
    Over Voltage Shut Down 20 40 80 VDC (max)
    Minimum Input Current 0 0 0 A (min)
    Full Load Input Current 3.2 2.0 1.0 A (max)
    Effciency by Model 81 83 84 %
    Swtiching Frequency 360 to 440 KHz, Factory set
    Operating Tempurature -40 to +65 °C, up to 105°C with derating of 2% per °C (no air flow)
    Storage Temperature -55 to +125 °C
    Relative Humidity 5 to 95 %, non-condensing

    If you need accessory information for this product, please use our Online Contact Us Form , our industrial sales team is here to help you find the accessories.

    WARNING:: The plastic used in cable products can expose you to lead and lead components, chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information go to www.P65Warnings.ca.gov
    [0] [true] [Yes] [No] [No]