Korenix JetNet 6810G-M12 8+2G Managed PoE Switch, DC24V to 48V Boost, w/8-port PoE (802.3af), M12

Korenix JetNet 6810G series, the revolutionary Gigabit Managed Industrial Power over Ethernet Switches with patented 24V to 48V Power booster technology, are specifically designed for making the deployment of standard PoE IP cameras feasible on buses, railcars, ships, harbors, etc. With the smart thermal detection function, the JetNet 6810G isolated power booster becomes an intelligent and reliable power control device for PoE vehicle applications in harsh environments with high temperature variations. The eight 10/100 TX PoE injector ports can deliver up to 120W power per unit and 15.4W per port by IEEE 802.3af standard to fulfill local increasing PoE demands. The two Gigabit Ethernet ports provide high speed uplink to connect with higher level backbone switches with Korenix MSR^TM network redundancy technology. Korenix RSR^TMcan recover the network failure in less than 5 ms. To work under vibration and shock environments, the industrial D-code M12 connectors (JetNet 6810G-M12) or rugged RJ connectors (JetNet 6810G-RJ) provide exceptional solid Ethernet and PoE connections.

Driving the IP Surveillance Market

Since the ratification of the Power over Ethernet standard in 2003, the Power over Ethernet technology becomes a trend; more devices adopt PD technology to obtain power through Ethernet cable eliminating the need of running separate power wirings to a remote device. The JetNet 6810G series is equipped with the new PSE solution, compliant with IEEE 802.3af standard and forced powering mode. It supports 8 PoE ports in End-span wiring architecture with up to 15.4w powering ability per port and 120W per unit, to drive the IP cameras for cross–street monitoring or WiMAX systems for internet access at train stations, airports or Hot-spots.

Power Budget Limitation with Priority Control
The JetNet 6810G series provides budget and priority control to ensure that the total power consumption will not exceed the power limit installed by user. It also provides budget control function to limit the output power in case if the PD device is not claimed right consumption numbers. This feature allows user to protect high priority PD devices from shut down caused by overloading of the power supply.

Isolated 24~57V DC PoE Booster for vehicle deployment

JetNet 6810G series is designed with the Korenix patented DC 24V to 48V boost technology for vehicle PoE applications where DC 48V power supply is not available. The DC booster supports High-pot isolation feature to protect the device from the lighting and surge of the Ethernet cable and meets IEEE mandate safety requirement of Power over Ethernet and UL safety requirement of TNV-1 circuit.

The isolated system design allows JetNet 6810G series efficiently powering outdoor PD equipments, such as Wireless AP,  WiMax systems, Outdoor IP cameras and other PoE-enabled devices. With the booster technology it provides fast, easy and cost-effective solution for configuring PoE networks on transportation and automation applications.

Smart Thermal & Power Booster Protection 
As states the rule of ”The Principle of Conservation of Energy”, the energy remains constant and cannot disappear in any isolated system, but can be converted to another form. This rule is the same in electrical circuit, where it can generate heat and become higher when the loading is more and therefore, can cause a system shut-down. 

To avoid this situation, JetNet 6810G series adopts thermal detector to check the temperature of DC booster and adjust the available PoE output to ensure the DC booster is working under safety temperature. This behavior refers to the output curve of power booster; Once the temperature exceeds the limit, system will turn off the PSE port. This feature makes JetNet6810G PoE switch an intelligent power control device that helps you to maintain the PD devices under specific temperatures.

Solid RJ45/M12 Connectors against Vibration and Shock
In most occasions, PD devices installed in industrial environments are being subjected to vibration, shock, dust and other environmental threats. Korenix has designed JetNet 6810G series with RJ and M12 connectors resistant to vibration and shock in order to best fulfill the requirements of various applications. Equipped with 8 M12 D-coded connectors, JetNet 6810G-M12 series can be used for upgrading industrial applications while delivering power along with data to PD devices in industrial machinery, factory automation, railways, marine applications etc. For outdoor networking applications, such as telecom, outdoor surveillance, wireless AP connections, JetNet 6810G-RJ PoE switches with 8 rugged RJ45 Ethernet connectors can be ideal solutions.

Comprehensive Redundant Solutions – Multiple Super Ring (MSR^TM)
The JetNet 6810G supports new generation ring technology - MSR^TM (Multiple Super Ring), which includes various new technologies for different network redundancy applications and structures. The JetNet 6810G allows aggregating up to 5 Rapid Super Rings, including 4 Fast Ethernet plus 1 Gigabit Ethernet Rings. With the MSR^TM technology, a node can be configured to multiple rings with the failover time in as little as 5ms and zero-second of restoration time. In addition, users can extend the ring topology by adding hundreds of JetNet series to meet the large-scale network needs without compromising the network speed. The MSR^TMalso allows the JetNet series to easily connect with core management switches via standard Rapid Spanning Tree Protocol or through multiple paths or nodes to increase the reliability by RDH^TM (Rapid Dual Homing )(RDH^TM) technology. By integrating MSR^TM and Link Aggregation Control Protocol (LACP) the JetNet series can enhance the link availability and increase the overall link capacity. Two or more Fast Ethernet connections are combined in order to increase the bandwidth and to create a resilient and redundant link.

Rapid Super ring (RSR^TM) Technology

Rapid Super Ring is the 2nd generation of Korenix Ring Redundancy technology. The recovery time is greatly improved from 30ms to few ms for both copper and fiber ring. The Ring master can be auto-selected by RSR engine. The 1st ring port of the R.M. is the primary path while the 2nd ring port of the R.M. is the block path. Once the primary path fails, the 2nd path will be recovered within few ms. Besides, the restoration time is also shortened to zero in the R.M. auto-selection mode.

Seamless Ring Port Restoration^TM
Seamless restoration is a new Korenix patented technology which can restore a failed ring without causing any loop problem, topology change and packet loss. With a 0 second restoration time, this mechanism eliminates any unstable status and guarantees the applications running non-stop.

Rapid Dual Homing (RDH^TM) Technology
Rapid Dual Homing is also an important feature of Korenix new generation Ring technology. It supports ring coupling with other vendors devices. Moreover, providing easy configuration and multiple redundancies, the failover time is much faster and the restoration time is zero ms. Uplinks can be auto detected and gathered into groups. In each group uplinks are sorted into primary, secondary and standbys based on their link speed. The uplink with the highest speed is more likely to be active path for data transmission. Link aggregation is also integrated into RDH^TM. An uplink connection can be a single link or several links aggregated as a trunk, which provides better redundancy and link capacity.

TrunkRing^TM

TrunkRing is a new feature in MSR which merges the two technologies of RSR and link aggregation. It takes advantages of aggregation to enhance the link redundancy, while increasing the link speed. The ring will open only if all the aggregated links are broken. Link aggregation can be achieved by either static trunk or LACP. Not all the link sections in a TrunkRing need to be the same. Ring links can be either symmetric or asymmetric. Some are a single path, and the others are aggregated by links where the number of links in a trunk group can be different. Users can enhance the link redundancy at different locations in accordance to the need. The link with less speed is more likely to be used as the backup path for restoring the network to full play capacity.

c

Link Aggregation Control Protocol

Link Aggregation Control Protocol allows users grouping multiple Ethernet ports in parallel to increase the link bandwidth. The aggregated ports can be viewed as one physical port, so that the bandwidth is higher than just one single Ethernet port. The member ports of the same trunk group can balance the loading and backup with each other. The LACP feature is usually used when higher bandwidth is needed for the backbone network. This is a cost-effective way for transfering much more data.

Auto Topology Discovery & Efficient Management through LLDP and JetView Pro i²NMS
JetNet 6810G supports topology discovery or LLDP (IEEE 802.1AB Link Layer Discovery Protocol) function that can help users to discover multi-vendor’s network devices on the same segment by an NMS system, which support LLDP function. With LLDP function, NMS can easily maintain the topology map, display port ID, port description, system description, VLAN ID, etc. 

Once a link failure happens, the topology changed events are updated to the NMS to help users easily maintain the network system. Besides the SNMP and LLDP protocols, JetNet 6810G series efficiently works with the Korenix patented JetView Pro i²NMS, which in addition to the autotopology discovery, also delivers MSR^TM group management, group IP assignment, firmware upgrade, configuration file backup/ restore ,SNMP MIB Browser /compile, etc. Furthermore, users can export the topology map to diverse formats, such as JPG, BMP, PNG and PDF, for easily managing and trouble-shooting the network. The user-friendly software allows administrators to discover devices automatically and efficiently manage the performance of the industrial network.

Outstanding Management and Enhanced Security
The JetNet 6810G series provides various network control and security features to ensure the reliable and secure network connection. To optimize the industrial network environment, JetNet 6810G series supports advanced network features, such as VLAN, IGMP Snooping, Quality of Service (QoS), Link Aggregation Control Protocol (LACP), Rate Control, etc. To avoid hacker’s attacks and ensure the secure data transmission, JetNet 6810G series features DHCP client, DHCP server with IP and MAC binding, 802.1X Access Control, SSH for Telnet security, IP Access table, port security and many other security features.

Product Category
Product Category	Managed Switch
Mechanical
Dimensions: WxHxD (mm)
Mounting
IP level
Enclosure
Data Rate and Number of Ports
Number of Ports
Fast Ethernet, 10/100 Mbps
Gigabit, 10/100/1000 Mbps
Interface
Interface Type
Fiber connector
PoE
M12 Connector
SFP
Digital I/O/Relay
Console
Bypass
Modular Design
Available Modular
Power
Power Input Type
Operating Supply Voltage
Power Consumption
Reliability
Operating Temperature
Redundancy and Backup Options
Redundancy Technology
STP/RSTP/PSTP/MSTP
Automatic Backup Configurator
Certification
Certification
UL 508 (Industrial Control)
EN 50155 (Rail Industry)
EN 50121-4 (Rail Industry)
EN 50121-3-2 (Rail Industry)
NEMA TS2 (ITS)
IEC 61850-3 (Power Industry)
IEEE 1613 (Power Industry)
IEEE 1588PTP (Power Industry)
DNV.GL (Marine)
ABS.LR.NK (Marine)
C1D2 (Oil & Gas)
ATEX (Oil & Gas)
Network Management and Control
Layer Level Switching
Modbus/TCP
Ethernet/IP
PROFINET
SNMP/RMON
LLDP
DHCP
IGMP Snooping/GMRP
QoS
VLAN 802.1Q
IEEE 802.1X
LACP (802.3ad)
Port Lock
IPv6

If you need accessory information for this product, please use our Online Contact Us Form , our industrial sales team is here to help you find the accessories.

Download DataSheet