The ION C2110 device provides an interface between 100Base-TX ports and 100Base-FX ports allowing users to integrate fiber optic ca- bling into 100Base-TX copper environments.

This Transition Networks's SFP unit fully comply with Multi-Sourcing Agreement (MSA). This compliance allows Transition Networks SFP module to be used on other MSA-compliant SFP platforms without any problems.

This converter will automatically re-establish link in all network conditions. Supports Transparent Link Pass Through which sends a link-loss signal over the fiber, instructing the remote converter to shut down the copper port thus notifying the end device while maintaining the fiber link between the two converters. Allows Pause signaling feature that temporarily suspends data transmission between two devices in the event that one of the devices becomes overwhelmed.

The x4120-1048 is a 10 Gigabit Ethernet copper to fiber media converter. It offers conversion technology by providing one 10GBase-T RJ-45 port and one pluggable 10GBase-X fiber SFP+ port. The open SFP+ port supports a wide variety of Transition Networks 10GE SFP+ fiber modules, as well as third party MSA compatible SFP+ modules.

The x4120 provides several 10G Ethernet enterprise and data center connectivity solutions. Since most 10G Ethernet switches support a combination of copper RJ-45 and open SFP+ ports, the x4120 allows users to convert either of these ports to the media type of their preference to match their network requirements, including direct attached copper SFP+ cables.

The x4120-1048 is a 10 Gigabit Ethernet copper to fiber media converter. It offers conversion technology by providing one 10GBase-T RJ-45 port
and one pluggable 10GBase-X fiber SFP+ port. The open SFP+ port supports a wide variety of Transition Networks 10GE SFP+ fiber modules, as well as third party MSA compatible SFP+ modules.

The x4120 provides several 10G Ethernet enterprise and data center connectivity solutions. Since most 10G Ethernet switches support a combination of copper RJ-45 and open SFP+ ports, the x4120 allows users to convert either of these ports to the media type of their reference to match their network requirements, including direct attached copper SFP+ cables.

Fiber Integration
Used in pairs or as a single unit, this mini media converter will ease the integration of fiber optic cabling into copper-rich Fast Ethernet environments

Extend Network Distance
Fiber supports the transmission of Fast Ethernet data over much longer distances than is possible twisted pair

Low-Latency Design
As a layer-1 design, this Mini converter will retransmit Fast Ethernet signals without any store-and-forward packet inspection delays found in other layer-2 devices

Transition Networks' serial RS232 to Fiber Media Converter allows you to extend the distance between serial connections with the use of fiber optic cable. This full-featured converter transmits the full complement of RS232 flow control/handshaking signals optically and supports full or half-duplex asynchronous data transmission at speeds up to 115Kb/s.

The diagnostic features included on this converter make installation easy and intuitive. A DTE/DCE switch eliminates the frustration over selecting the appropriate cable. A loop-back switch allows for complete diagnostic testing prior to system turn-up or during troubleshooting. Unit and Port LEDs allow for quick status information of the converter.

Transition Network's serial RS232 to Fiber Media Converter allows you to extend the distance between serial connections with the use of fiber optic cable. This full-featured converter transmits the full complement of RS232 flow control/handshaking signals optically and supports full or half-duplex asynchronous data transmission at speeds up to 115Kb/s.

Fiber Integration
Used in pairs or as a single unit, this mini media converter will ease the integration of fiber optic cabling into copper-rich Gigabit Ethernet environments

Extend Network Distance
Convert 1000Base-T ports over to 1000Base-SX/LX on a port-by-port basis. Fiber supports the transmission of Gigabit Ethernet data over much longer distances than is possible twisted pair

Low-Latency Design
As a layer-1 design, this Mini converter will retransmit Gigabit Ethernet signals without any store-and-forward packet inspection delays found in other layer-2 devices

Fiber Integration
Used in pairs or as a single unit, this mini media converter will ease the integration of fiber optic cabling into copper-rich Fast Ethernet environments

Extend Network
Distance Fiber supports the transmission of Fast Ethernet data over much longer distances than is possible twisted pair

Low-Latency
Design As a layer-1 design, this Mini converter will retransmit Fast Ethernet signals without any store-and-forward packet inspection delays found in other layer-2 devices

The Transition Networks TN-GLC-xxx series small form factor pluggable (SFP) tranceiver modules are designed to install in any SFP port allowing for 1000Base-T, 1000Base-SX or 1000Base-LX interfaces to the network through the SFP connector. The TN-GLC-xxx tranceivers are Cisco compatible* and are designed for bi-directional serial-optical data communication such as Gigabit Ethernet or fiber channel at speeds up to 1.25 Gbps.

Transition Network's Gigabit Ethernet media converter connects 1000Base-T shielded or unshielded twisted-pair copper cable to 1000Base-SX fiber optic cable.

This Transition Networks's SFP unit fully comply with Multi-Sourcing Agreement (MSA). This compliance allows Transition Networks SFP module to be used on other MSA-compliant SFP platforms without any problems.

Save money by purchasing Fast Ethernet devices with lower cost multimode fiber interfaces and use converters to introduce single mode fiber only where you need it. Transition Networks F-SM-MM-02-NA Fast Ethernet Media Converter extends Fast Ethernet or ATM over singlemode fiber-optic cable up to 20 km.